Customer CaseValencia, Spain / Scrap Metal Recycling

250-Ton Metal Baler Replacement in Valencia, Spain

A mid-sized scrap recycler in Valencia replaced an aging European-brand baler with a Dershan Y83-250. After more than 18 months of stable operation, the customer reported higher processing output, denser bales and lower energy use.

Blue side turn-out hydraulic metal scrap baler in the Dershan workshop
Side turn-out metal baler — equipment reference image from the Dershan library, not the Valencia installation.

Project context

A mid-sized scrap metal recycling business in Valencia, Spain handles stamping offcuts, appliance scrap, thin sheet metal and workshop trimmings. Its existing European-brand baler had become increasingly unreliable as it aged.

The customer was looking for a practical replacement: sufficient pressing force, dependable operation through the working day and a manageable purchase and maintenance cost. The aim was to improve everyday production without allowing repair delays to dictate the processing schedule.

Material & site requirements

The aging baler created three connected problems:

  • Loose bales and excessive storage demand: inadequate pressure left material insufficiently compacted and increased the space needed to hold processed scrap.

  • Slow processing and high energy use: long cycles disrupted the daily work rhythm and restricted output.

  • Expensive maintenance: costly spare parts and long delivery times made servicing difficult to plan.

The replacement needed to handle the customer’s sheet-metal and workshop scrap streams while improving bale consistency and serviceability.

Steel stamping offcuts and workshop sheet-metal trimmings

Stamping scrap — material reference from the image library.

Loose light ferrous scrap for hydraulic baling

Light ferrous scrap — material reference from the image library.

Equipment & configuration

The customer selected a Dershan Y83-250 metal baler. The configuration combines a 250-ton pressing force with PLC automatic control and wear plates at key locations.

ItemProject specification
ModelY83-250
Pressing force250 tonnes
Motor configuration2 × 30 kW
Charging chamber2200 × 1400 × 1000 mm
Bale cross-section500 × 500 mm
ControlPLC automatic control
Wear protectionWear plates at key locations

The 500 × 500 mm specification describes the bale cross-section; a bale length was not specified in the project information. The installed motor ratings are not a measurement of energy consumed per tonne of scrap.

Side turn-out metal baler and control cabinet in the workshop

Side turn-out baler from the Dershan image library; equipment illustration rather than a Valencia site photograph.

Operation and maintenance support

The replacement was intended to provide a steady baling step for the recycler’s existing material flow. PLC automatic control supports the operating sequence, while the wear plates address abrasion at selected working surfaces.

Support was also part of the replacement decision. The customer reports that remote troubleshooting and prompt spare-parts supply helped maintain production during the busy season. This addressed a recurring difficulty with the previous machine: long waits for expensive replacement parts.

For an aging-machine replacement, the service plan should be reviewed alongside the machine itself: wear-part availability, maintenance access, troubleshooting arrangements and the expected time to return equipment to service.

Customer-reported results after 18+ months

After more than 18 months of stable operation, the customer reported the following results compared with the previous baler:

MeasureCustomer-reported result
Work efficiencyImprovement of more than 30%
Daily processing volumeIncrease of 10–15 tonnes per day
Storage spaceApproximately 25% saved as bale density improved
Energy useReduction of 12–18%
Busy-season continuityNo production stoppages reported for the cited busy season
Further investmentCustomer plans to purchase another Y83-series baler

These results are customer feedback from this installation, not guaranteed performance for other sites. The supplied account does not specify the energy comparison’s metering period or whether it was normalized per tonne.

Selection lesson: when replacing an aging baler, compare sustained output, energy consumed per tonne and lifetime maintenance cost alongside pressing force. A higher installed motor rating or a larger pressure figure alone does not establish the lowest operating cost.

Frequently asked questions

Why did this Valencia recycler replace its old baler?

The aging machine produced loose bales, used substantial energy, cycled slowly and depended on expensive spare parts with long delivery times.

What material streams does the case cover?

Stamping offcuts, appliance scrap, thin sheet metal and workshop trimmings. The actual feed condition and preparation requirements should be reviewed for each project.

What does the 500 × 500 mm bale specification mean?

It is the specified bale cross-section. The project information does not provide a bale length, so it should not be interpreted as a complete three-dimensional bale size.

Are the reported energy savings guaranteed?

No. The customer reported 12–18% lower energy use than its previous baler. A new project should compare measured energy consumption under equivalent material, output and operating conditions.

Does the case demonstrate guaranteed zero downtime?

No. The customer reported no production stoppages during the cited busy season, supported by remote troubleshooting and prompt spare parts. This is a site-specific operating experience, not a general uptime guarantee.

How should a similar replacement project be evaluated?

Review feed materials, required bale dimensions, daily working hours, measured output, energy records and spare-parts needs. Explore side turn-out metal scrap balers, compare the wider metal baler range, or contact Dershan about a replacement configuration.

Need equipment matched to your material and production target?

Contact Our Team