News & InsightTechnical Knowledge

Vertical vs. Horizontal Metal Chip Briquetting Presses: Which Should You Choose?

Press orientation is only one selection factor. Compare the complete material route, operating duty and installation needs before choosing a briquetting system.

Horizontal hydraulic metal-chip briquetting press with feeding equipment and control cabinet in a workshop.
Horizontal briquetting equipment from the image library. Feeding, guarding and auxiliary equipment must be confirmed for each configuration.

Compare the complete chip-handling system

Choosing between vertical and horizontal briquetting presses starts with a practical question: how will your chips move through the entire system? The direction of the pressing ram influences equipment layout, but it does not independently determine capacity, density or suitability for continuous production.

For aluminum, iron and brass chips, the stronger proposal is the one that matches material preparation, feeding, pressing and collection to actual production conditions. Comparing these stages helps buyers avoid selecting a machine on appearance or motor power alone.

What vertical and horizontal actually describe

A vertical briquetting press compresses its charge through a vertically arranged pressing structure. A horizontal machine uses a horizontal pressing arrangement. Both require suitable feedstock, controlled charging of the forming area and a defined route for finished briquettes.

The DSB Vertical Metal Chip Briquetting Press has PLC automatic or manual control, continuous push-out discharge and configurable mobile-bin, hopper or steel-chain conveyor feeding. Its suitability depends on prepared chips and the selected configuration.

The DSH Horizontal Metal Chip Briquetting Press uses horizontal hydraulic compression, an upper feeding assembly and push-out discharge. Its automatic/manual control configuration and auxiliary equipment require confirmation in the proposal.

These descriptions establish real differences in arrangement. They do not establish that one series always produces denser briquettes, handles more material or uses less energy.

Vertical metal-chip briquetting press with upright hydraulic cylinder and separate power unit.

Vertical press reference from the image library. Compare the full layout and material trial results rather than orientation alone.

Compare the chips before comparing the machines

The same metal can produce very different swarf. Short, flowable chips, long tangled turnings and fine material create different feeding and handling demands. Confirm the alloy, particle-size range, loose bulk density, contamination and residual fluid for every intended stream.

Aluminum chips: Establish the actual alloy and whether the stream includes long curls, fine chips or mixed forms. Assess bridging, metering consistency and fluid handling. Downstream remelting requirements should help define the required briquette size and condition; the press does not certify furnace readiness.

Iron chips: Distinguish cast-iron chips from steel turnings rather than treating every ferrous stream alike. The actual chip form and fines content can change the preparation, feeding and tooling assessment. Remove unsuitable foreign material through an agreed process.

Brass chips: Keep the grade and source identifiable, particularly where several copper-alloy jobs share a collection route. Specify how changeovers and residual material will be managed. A result obtained with aluminum or cast iron does not establish brass performance.

Both DSB and DSH product information calls for material-specific assessment. Fine powders are not automatically suitable, and long tangled turnings may need size reduction before metered feeding.

Feeding often determines sustained output

A press cannot maintain its intended production rate if the forming chamber receives an irregular supply. Review the route from the collection container to the metering area, including loading height, transfer method and usable buffer capacity.

Ask how the proposed arrangement responds when chips bridge, arrive in a surge or contain an oversized piece. Any equipment for size reduction, drainage or separation should be identified in the scope rather than assumed to be included with the press.

Check the conveyor or bin interface against the real material volume as well as mass. Low-bulk-density chips can occupy substantial space before compaction. Feeding reliability needs to be demonstrated with the expected chip forms, not inferred from a photograph of a full hopper.

Continuous operation needs more than automatic controls

An automatic pressing cycle is only one part of sustained production. Incoming material supply, fluid collection, cooling, finished-briquette removal and maintenance arrangements must all support the planned shift pattern.

The DSB page describes continuous push-out discharge. That feature still requires a receiving arrangement that does not become full or obstructed. For DSH, confirm the intended operating duty and collection method in the selected configuration rather than assuming that horizontal geometry guarantees continuous operation.

Compare accepted briquette mass over elapsed production time, including normal feeding and collection interruptions. Keep machine-cycle figures separate from sustained line output. Likewise, motor rating identifies installed equipment; it does not establish electricity consumption per tonne. If energy use matters, measure it over the same operating period as accepted output.

Plan the installation around every interface

Use a configuration drawing to compare the complete space requirement. Include hopper loading, access above the feed assembly, hydraulic equipment, cooling, fluid collection and the briquette discharge route. A compact machine footprint may still require substantial operating and maintenance space.

Confirm tooling-removal access and how service personnel will isolate the machine safely. For an integrated line, define the signals exchanged with upstream and downstream equipment, along with fault response, buffer-full conditions, emergency stops and restart responsibilities. Guarding and control interfaces need a coordinated design.

Floor loading, available height, electrical supply and cooling conditions should be reviewed before layout approval. Neither “vertical” nor “horizontal” provides enough information to settle these requirements.

Choose the configuration that resolves your constraints

A vertical DSB is worth assessing when its pressing arrangement, loading options and discharge route fit your installation and material. A horizontal DSH is worth assessing when its horizontal forming layout, upper feed and push-out route suit the proposed process.

The final choice should follow evidence about feeding stability, accepted output, briquette quality, service access and integration. Where both arrangements are feasible, compare proposals using the same feedstock and operating assumptions. Document the conditions under which each quoted result applies.

Request a material-specific comparison

Contact Dershan with chip photographs, alloy details, fluid condition, hourly generation, shift pattern and a simple layout showing loading and collection points. Include your downstream briquette requirements and any planned material changeovers. Ask for a DSB-versus-DSH assessment that identifies preparation equipment, supplied auxiliaries, control interfaces and performance items requiring confirmation.

Need equipment matched to your material and production target?

Contact Our Team