News & InsightTechnical Knowledge

Alligator Shear vs. Gantry Shear: Which Handles Your Steel Scrap?

Choose a scrap shear around the steel you actually handle, from pipe and rebar to plate offcuts, with clear checks for section size, feeding and daily output.

Hydraulic alligator shear with hinged cutting jaw and separate hydraulic power unit in a workshop.
Alligator-shear reference from the image library. Approved cutting limits depend on the material, section and selected machine.

Match the shear to the steel scrap and handling route

A pile of steel scrap can contain thin-walled tube, solid rebar and wide plate offcuts. All three may need shortening, but they present very different cutting and handling demands. Selecting a shear only by its advertised force can leave the yard with a machine that makes a cut yet struggles to keep the process moving.

The useful comparison is between the complete cutting stations: how each piece reaches the blade, how its section is presented, how many cuts it needs and how the finished pieces leave. An alligator shear and a gantry shear have different cutting geometries, but neither machine name defines a universal material limit or a guaranteed hourly output.

What changes between the two cutting arrangements?

An alligator shear uses a pivoting upper jaw that closes against a lower blade. The Dershan ASF is a hydraulic alligator shear intended for prepared bars, rebar, profiles, pipe and suitable offcuts. Its compact body can suit a dedicated batch-cutting station, provided the feeding method, stock support and surrounding work area are planned together.

A gantry shear places a vertically guided cutting assembly within a rigid frame. The Dershan HS product illustrations show this vertical cutting head. The full installation still needs a defined loading arrangement, hydraulic power system, controls, guarding and cut-piece collection.

This distinction matters when comparing quotations. A gantry cutting head is not automatically a complete automatic processing line, and a scrap shear does not automatically produce compacted bales. Ask for every required component to be listed in the supply scope.

Gantry shear installation with upright cutting frame and scrap receiving area.

Example gantry-shear installation from the image library. The HS cutting head is not a complete line; any feed box, conveyor and auxiliary equipment must be specified separately.

Steel pipe: outside diameter is only the starting point

For round pipe, record the outside diameter, wall thickness and steel grade. For square or rectangular tube, provide both outside dimensions and the wall thickness. Also show whether the material is straight, flattened, bent, nested or mixed with other sections.

A large thin-walled tube and a smaller thick-walled tube can create very different cutting demands. Several pipes placed together are another condition again. Do not transfer a single-piece rating to a bundle simply because the bundle fits the opening.

For an alligator station, review how the longest pipe is supported and positioned throughout the cut. For a gantry station, establish the permitted cutting envelope and the equipment that presents the pipe to the vertical blade. In both cases, include the required finished length: shorter output may mean more cuts, more repositioning and more collection work per tonne.

Rebar and solid bar: identify the demanding section

Rebar enquiries should include grade, diameter, incoming length and whether bars are straight, bent or tied together. Solid square and rectangular bars need their full cross-section dimensions. Include the largest and toughest sections that occur in normal work, not only the easiest sample.

Prepared individual bars or a controlled section mix may be well suited to an ASF alligator-shear assessment. For a proposed HS station, review the largest section and the quantity presented together, along with the feeding arrangement. Neither a jaw opening nor a gantry opening proves that a particular bar or bundle is within the machine's cutting limit.

If mixed bundles are unavoidable, define their permitted composition and arrangement during the technical review. Uncontrolled bundles should not become the basis for a performance promise.

Steel plate: thickness and engaged width belong together

Plate thickness alone is not enough to select a shear. Provide the width engaged by the blade in each cut, the grade, the offcut shape and the required finished size. Narrow strips and broad plate pieces of the same thickness do not represent the same cutting task.

Ask how each plate will be lifted, supported and aligned. Review the permitted blade length, opening and cut sequence for the chosen configuration. Where plate is curled, reinforced, attached to another section or mixed with unknown grades, send photographs and measurements before treating it as ordinary flat plate.

Large or awkward material can justify evaluating a gantry cutting station, but the handling arrangement and actual section limits must support that choice. Do not assume every gantry shear accepts any oversized steel scrap.

Compare daily output using the whole working cycle

Cuts per minute is a machine reference, not a yard-production result. Useful output includes loading, supporting the stock, positioning each cut, operating the shear, moving finished pieces and the normal interruptions of the shift.

Use the same representative scrap mix and target cut lengths when comparing proposals. Record:

  • Processed mass over elapsed working time, not only blade-stroke time.

  • The number of operators and the loading equipment used.

  • Normal pieces as well as the most demanding approved sections.

  • Delays caused by repositioning, sorting or clearing the receiving area.

  • The blade condition, machine configuration and operating limits used in the assessment.

A layout that lets one machine receive material consistently may outperform a poorly arranged station with a larger nominal force. The appropriate capacity is the sustainable result for your actual feed and handling system.

Allow room for people, lifting equipment and maintenance

The machine footprint is only part of the installation. Show the longest incoming stock, crane or grabber approach, operator location, finished-scrap container and service access on a site plan. Keep vehicle movements and protected operating areas clearly separated.

Plan blade inspection and replacement access before the station is installed. Guarding, emergency stops and control arrangements must be agreed for the complete system. Qualified personnel must follow the machine manual and lockout and stored-energy procedures for maintenance. Sealed vessels, pressurized items, batteries and hazardous residues must not enter an ordinary scrap-shearing process.

A practical way to narrow the choice

Start an alligator-shear review when the main task is controlled batch cutting of prepared bars, rebar, profiles or suitable offcuts and the loading workflow fits a pivoting-jaw station.

Start a gantry-shear review when a vertically guided cutting station is a better fit for the assessed material envelope and planned handling system. Confirm the complete equipment scope rather than inferring it from a photograph or rendering.

For either route, the final decision should rest on approved material limits, representative cutting evidence and a workable site layout. A familiar machine type is useful; a configuration matched to your scrap is more valuable.

Ask Dershan to compare the cutting options

Send clear scrap photos, steel grades, maximum bar or tube dimensions, pipe wall or plate thickness, required cut length, daily tonnage and operating hours. Add your preferred feeding method and a simple drawing of the available area.

Explore the ASF Hydraulic Alligator Shear, review the HS Vertical Gantry Shear, or request a material-specific recommendation. These details give the technical team a useful basis for comparing the cutting head, handling equipment and project scope.

Need equipment matched to your material and production target?

Contact Our Team