Dual main cylinders: an HBK hydraulic compression arrangement for metal scrap baling.
Metal Balers
Dual Main Cylinder Compactor for Metal Recycling
Maintaining scrap-grade separation | HBK series
Dual Main Cylinder Compactor for Metal Recycling for prepared metal scrap. Maintaining scrap-grade separation. Review HBK hydraulic configuration, chamber dimensions and grab-out bale handling for your project.
PRODUCT VIDEO
Dual Main Cylinder Compactor for Metal Recycling video
01 / PRODUCT DESCRIPTION
Maintaining scrap-grade separation
Hydraulic compression and handling for your recycling project.
HBK Specifications, Applications & Configuration
Dual-main-cylinder hydraulic baling for prepared scrap. Select the configuration around your material, bale requirements and site layout.
The Dual Main Cylinder Compactor for Metal Recycling is an HBK-series horizontal hydraulic baler for compacting prepared metal scrap into square bales. Its dual main cylinder arrangement is paired with grab-out bale collection for subsequent handling, storage and transport.
Maintaining scrap-grade separation
Where downstream recyclers require separated grades, plan material identification and handling before baling. Use the selected chamber for prepared, approved feed and keep the bale identification process aligned with storage and dispatch. Material quality remains part of the recycling specification.
Use the technical table below as a series reference. Confirm the actual feed dimensions, material grade, working schedule and selected configuration before ordering. For output assessment, consult the scrap metal baler production planning guide.
02 / MATERIALS & OUTPUT
Applicable Scrap & Bale Output
Prepare and assess the incoming material before selecting a machine.
This dual-main-cylinder baler compacts prepared stainless steel scrap, waste reinforcing bars, light-gauge ferrous scrap, copper tubes and depolluted end-of-life vehicle metal scrap. Select the machine configuration for the actual grade, thickness, hardness and feed dimensions.
Stainless steel scrap for hydraulic baling: Sort stainless steel by grade; assess thickness and piece dimensions for the selected chamber.
Waste reinforcing steel bars before preparation: Cut long reinforcing bars to the approved feed size and remove concrete and other contaminants before baling.
Light-gauge ferrous sheet and strip scrap: Thin sheet, strip and stamping offcuts can be compacted into manageable bales; assess springback and loading consistency.
Scrap copper tubes for separate-grade recycling: Keep copper tubes separate from ferrous scrap, drain residual fluids and confirm dimensions before loading.
End-of-life vehicle body scrap awaiting preparation: Vehicle scrap must be dismantled and depolluted before baling; batteries, fuels and pressurized parts must be removed. Whole-vehicle acceptance is model-dependent.
Sort different metals into separate batches. Oversized or tangled pieces require cutting or preparation before loading. Bale mass and density vary with material and configuration; agree the output dimensions with the receiving recycler or mill.
Photographs illustrate material types rather than a matched production trial. See the stamping steel scrap guide for related preparation advice.
03 / STRUCTURE & FEATURES
Equipment features.
Structure & Features
Choose the components and options that match your application.
Horizontal chamber: choose the chamber dimensions to suit prepared feed and loading access.
Grab-out handling: coordinate loading and bale collection equipment with the working area.
Wear protection: interchangeable NM450 or Hardox450 wear plates are listed as configuration options.
Control choice: PLC automatic or manual control, with optional remote control.
Hydraulic cooling: water cooling or an industrial chiller can be specified for the installation.
Confirm selected components and accessories in the quotation. Equipment images show HBK-family examples and do not define the supply scope of every configuration.
04 / WORKING PRINCIPLE
Baling Process & Maintenance
Coordinate preparation, loading, compression and collection.
Sort the scrap, remove unsuitable items and prepare pieces to the agreed feed specification.
Load the chamber using the approved handling method and keep personnel outside the operating area.
Run the compression sequence specified for the selected control system.
Remove the completed bale with the approved grab and transfer it to a designated storage area.
Inspect hydraulic connections, wear surfaces and cooling equipment at the intervals in the machine instructions.
For planning, measure the complete loading, compression and collection cycle. The baler throughput guide explains how handling and downtime affect actual output.
05 / TECHNICAL REFERENCE
HBK Series Technical Parameters
Series ranges and options; confirm a model-specific specification.
| Parameter | HBK series reference / configuration option |
|---|---|
| Series | HBK |
| Layout / drive | Horizontal / hydraulic |
| Main compression arrangement | Dual main cylinders |
| Bale removal | Grab-out |
| Working pressure | 21.5 MPa |
| Chamber length range | 2,000–4,000 mm |
| Chamber width range | 1,500–3,000 mm |
| Chamber height range | 1,000–1,400 mm |
| Bale cross-section range | 500 × 500 to 800 × 800 mm |
| Cycle reference | 120–180 seconds per bale; no-load reference 120 seconds |
| Machine weight range | 45,000–150,000 kg |
| Oil tank volume range | 4,000–15,000 L |
| Electrical supply options | Three-phase, 220–660 V, 50/60 Hz; selected to suit the installation |
| Control options | PLC automatic or manual |
| Remote control | Optional |
| Construction steel | Q235B |
| Wear-plate options | NM450 or Hardox450; interchangeable plates |
| Cooling options | Water cooling or industrial chiller |
These are series ranges and options from the HBK specification sheet, not the fixed specification of one machine. Final dimensions, utilities and cycle performance depend on the selected configuration and material. Compression force, installed motor power, throughput and bale weight are confirmed in the model-specific proposal.
07 / QUESTIONS & SUPPORT
Product questions,
answered.
Frequently Asked Questions
Practical answers on materials, operation and configuration.
What materials can this HBK baler process?
Prepared stainless steel, waste rebar, light-gauge ferrous scrap, copper tubes and depolluted vehicle metal scrap can be processed subject to the selected configuration. Sort metal grades and cut oversized bars to the approved feed dimensions. Vehicle scrap requires dismantling and depollution, including removal of batteries, fuels and pressurized components; whole-vehicle acceptance is model-dependent.
How is the finished bale removed?
The HBK sheet specifies grab-out removal. The installation therefore needs a suitable handling arrangement and space for collecting and stacking bales. Confirm the grab, lifting capacity and equipment supply scope with the machine proposal.
Are all the listed parameter ranges available on one machine?
No. The table describes the HBK series and its configuration options. Chamber dimensions, utilities, controls and other ratings must be combined into one selected specification. Ask for a model-specific drawing and parameter schedule.
Is automatic control available?
The sheet lists PLC automatic and manual control alternatives, with remote control as an option. Choose the control arrangement according to the feeding process, staffing and site requirements; confirm the supplied functions before ordering.
How should production capacity be evaluated?
Use a representative material sample and include loading, compression, bale removal and ordinary interruptions in the measurement. Material shape, preparation and handling all affect output. Refer to the production planning guide when comparing proposals.
Does compaction replace scrap sorting?
No. Sorting, contamination control and grade identification remain necessary according to the receiving recycler requirements. Confirm the accepted feed specification.
Equipment Recommendation
Tell Us About Your Material and Capacity
Share the key operating conditions below so our team can compare suitable equipment and prepare a practical configuration.

