Metal Balers

Dual Main Cylinder Hydraulic Metal Baler

HBK hydraulic baling with configuration and inspection guidance

HBK horizontal hydraulic baler with twin main cylinders and grab-out handling for prepared steel sheet and plate offcuts. Specify the hydraulic baler around site operating requirements.

HBK familyTwin main cylindersHydraulic compressionGrab-out bale handling
Suitable materials

PRODUCT VIDEO

Dual Main Cylinder Hydraulic Metal Baler video

01 / PRODUCT DESCRIPTION

Specify the hydraulic baler around site operating requirements

Application-led selection within the HBK family.

Specify the hydraulic baler around site operating requirements

HBK family guidance for prepared steel sheet and plate offcuts. Confirm the selected machine and application before ordering.

The HBK dual-main-cylinder hydraulic metal baler uses a horizontal hydraulic layout to compress prepared scrap, with grab-out handling for bale collection. Prepared steel sheet and plate offcuts are the focus of this page. The configuration review should cover the material as well as operating controls, electrical supply, service access and the loading and collection arrangement.

HBK identifies a product family rather than one fixed set of numerical ratings. This product title describes that family. The final machine specification should follow an application review and an agreed supply scope.

02 / MATERIALS & OUTPUT

Prepared steel sheet and plate offcuts

Describe the material in its normal working condition.

Material information should include grade when known, thickness, maximum dimensions and any coatings or contamination that may affect handling or acceptance. Identify sharp or projecting offcuts and establish an approved means of preparing and moving them. Any unfamiliar material should be reviewed before it is added to the agreed feed stream.

The material scope described here does not approve every metal form or thickness. Confirm acceptable feed against the selected machine and keep unsuitable items out of the charging stream. See light-gauge ferrous scrap and stamping steel scrap for related application considerations.

Loose thin strip and sheet-metal offcuts
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.
Formed sheet-metal stamping remnants
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.
Perforated sheet skeletons and trim
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.
Loose bent sheet and strip remnants
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.

03 / STRUCTURE & FEATURES

Equipment features.

HBK-family hydraulic metal baler with twin main cylinders; equipment reference

Twin main cylinders and selected configuration

Confirm architecture, options and supply scope together.

The HBK source lists PLC automatic control or manual control as alternatives, with remote control optional. These are configuration choices, not a promise that every machine contains every control mode. Agree the selected arrangement and operating responsibilities in the quotation, then use the instructions provided for that actual machine rather than a generic online sequence.

Interchangeable wear plates are listed at series level. Their selected material and replacement requirements belong in the confirmed specification. Equipment images illustrate the machine arrangement; material and bale photographs are examples, not measured evidence of HBK output, density or material limits.

04 / WORKING PRINCIPLE

Operating sequence and site planning

Coordinate material preparation, compression and collection.

Build the operating plan around the selected controls and site handling equipment. Include an inspection routine, a defined method for reporting faults, and access for authorized service personnel. If abnormal movement, leakage or damage is found, follow the machine instructions and site isolation procedure instead of attempting adjustments during a compression cycle.

The general sequence is material inspection and preparation, loading by the approved method, hydraulic compression under the selected controls, and grab-out bale collection. Follow the machine-specific operating instructions and keep people clear of the chamber and moving equipment. Never enter or clear the chamber while the machine can operate; maintenance and blockage removal require authorized isolation procedures.

05 / TECHNICAL REFERENCE

HBK specifications and selection

Series attributes require machine-specific confirmation.

Mechanical attributeHBK series reference / option
Bale shape referenceSquare / cube; confirm selected dimensions
Feeding alternativesGrabber or manual, subject to the specified installation
DriveHydraulic drive
Motor voltageCustomized; confirm site supply and selected model
Remote controlOptional
Wear plate replacementInterchangeable

The parameter table presents selected HBK series attributes, not a separate hardware model created by this product title. Confirm the final configuration against the actual scrap, site utilities and handling plan. Force, installed power, chamber dimensions, bale dimensions and production expectations require a consistent machine-specific specification rather than values combined from unrelated ranges.

07 / QUESTIONS & SUPPORT

Product questions,
answered.

HBK application questions

Six practical answers for material and equipment selection.

Are automatic control and remote control both standard?

The source offers PLC automatic control or manual control and describes remote control as optional. Confirm the exact arrangement in the selected machine specification. Control wording alone does not establish an unattended production line or remove the need for trained operators and a defined loading and collection procedure.

Which materials does this page cover?

The application described is prepared steel sheet and plate offcuts. Suitability depends on actual material properties, dimensions and preparation. The stamping steel scrap application provides useful context, but it does not replace review of the feed proposed for your selected HBK configuration.

What should be confirmed about the finished bale?

Agree the receiving recycler's requirements, intended handling method, dimensions and acceptable bale condition. Do not infer a fixed weight or density from photographs. Include these requirements in the quotation checklist so that material preparation, equipment selection and downstream handling are considered together.

How should expected throughput be assessed?

Include normal charging, compression and grab-out collection in the production assessment. Material variation and handling availability can change the result. The throughput planning guide explains why accepted bale mass and elapsed working time matter more than an isolated cycle or cylinder count.

What checks belong in the operating routine?

Follow the selected machine's operating and maintenance manual for checks of guards, hydraulic connections, wear surfaces and controls. Stop and report abnormal conditions through the site procedure. Servicing or blockage removal requires authorized isolation of all energy sources. Ask Dershan about model-specific inspection requirements when confirming the equipment.

How do I request an HBK configuration review?

Send representative material photographs, grade if known, thickness and piece dimensions, daily quantities, operating hours, electrical supply and bale requirements through DSBale contact. Include the proposed loading and collection arrangement. These details allow the enquiry to address the actual application without treating this title as a separate hardware SKU.

Equipment Recommendation

Tell Us About Your Material and Capacity

Share the key operating conditions below so our team can compare suitable equipment and prepare a practical configuration.

✓ Material & Capacity Review✓ Configuration Recommendation✓ Pricing & Lead-Time Inquiry

We use this information only to respond to your equipment inquiry.