Metal Balers

Heavy Duty Scrap Metal Baler with Twin Main Cylinders

HBK baling with material review and downstream bale requirements

Heavy Duty Scrap Metal Baler with Twin Main Cylinders from the HBK family, with horizontal hydraulic compression, twin main cylinders and grab-out handling for assessed steel offcuts.

HBK familyTwin main cylindersHydraulic compressionGrab-out bale handling
Suitable materials

PRODUCT VIDEO

Heavy Duty Scrap Metal Baler with Twin Main Cylinders video

01 / PRODUCT DESCRIPTION

Feed preparation and bale acceptance with HBK

An application-focused presentation of the HBK baler family.

Feed preparation and bale acceptance with HBK

HBK family guidance for prepared steel sheet and plate offcuts. Confirm the selected machine and application before ordering.

The Heavy Duty Scrap Metal Baler with Twin Main Cylinders describes an HBK horizontal hydraulic baler with grab-out bale collection. The two main cylinders are part of its compression arrangement. This page focuses on the connection between prepared steel sheet or plate offcuts and the bale requirements of the receiving recycler. It is an application-oriented presentation of the HBK family, not a claim of a separately tested heavy-scrap model.

Selection should consider what enters the chamber and what must leave the site. Record acceptable material grades, receiving requirements and the equipment used to collect and transport completed bales. A compact-looking bale in a photograph does not establish its mass, density, dimensions or suitability for a particular receiving operation.


02 / MATERIALS & OUTPUT

Prepared Steel Sheet and Plate Offcuts

Define the feedstock before specifying the machine.

Define the prepared feed before discussing bale specifications. Include steel grade, actual thickness, maximum dimensions, shape and contamination. Long or awkward offcuts may require preparation subject to the selected equipment's documented limits. Heavy duty wording does not authorize feeding complete structures, heavy beams or unspecified thick plate, and it should not replace a material review.

Keep representative samples or photographs of the normal stream and its occasional extremes. Explain any receiving restrictions on coatings, mixed grades or contamination. Material and bale photographs on a product page illustrate physical forms; unless a documented trial identifies them, they should not be treated as measured before-and-after results from a particular HBK machine.


Loose thin strip and sheet-metal offcuts
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.
Formed sheet-metal stamping remnants
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.
Perforated sheet skeletons and trim
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.
Loose bent sheet and strip remnants
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.

03 / STRUCTURE & FEATURES

Equipment features.

HBK-family hydraulic metal baler with twin main cylinders; equipment reference

Twin Main Cylinders and Configuration

Confirm controls, wear components and handling interfaces.

Horizontal hydraulic layout: HBK combines a charging chamber with twin-main-cylinder compression and grab-out bale collection. Confirm the final hydraulic sequence in the selected machine documentation.

Control selection: the series source lists PLC automatic or manual control. Optional remote control requires explicit confirmation in the supply scope.

Wear components: the source identifies interchangeable wear steel plates and NM450 or Hardox450 alternatives. Confirm the selected material and replacement details in the proposal.

Handling interfaces: specify approved loading and bale collection equipment, operating clearances and protected work areas. A grab-out designation does not establish an included crane.

Review guards, interlocks, emergency stops and maintenance access with the final configuration. Product illustrations and a series-level feature list do not replace machine-specific operating instructions or installation documentation.


04 / WORKING PRINCIPLE

Loading, Compression and Grab-out Collection

Plan the complete approved operating sequence.

  1. Prepare: sort approved offcuts, check dimensions and exclude batteries, sealed or pressurized containers and hazardous contamination.

  2. Load: use the approved feeding method with personnel outside the operating zone.

  3. Compress: operate the documented hydraulic sequence under the selected control arrangement.

  4. Collect: remove the bale using suitable grab-out handling equipment and the designated route.

  5. Reset: complete the prescribed checks before the next charge.

Only trained personnel should operate the equipment. Follow the machine manual and site isolation procedures for inspection, clearing obstructions or maintenance, including stored hydraulic energy. Never reach into the chamber or attempt to reposition material during operation.


05 / TECHNICAL REFERENCE

HBK Series Parameters and Selection

Selected source attributes require a model-specific proposal.

The table presents selected HBK series attributes, not a complete model specification. Confirm the final combination, material limits, chamber dimensions, force, power and bale requirements in the technical proposal. Numerical output and bale properties require defined feedstock and operating conditions.

Mechanical attributeHBK series reference / option
Motor voltageCustomized; confirm site supply and selected model
Construction steelQ235B; machine construction steel
Feeding alternativesGrabber or manual, subject to the specified installation
DriveHydraulic drive
Bale shape referenceSquare / cube; confirm selected dimensions
Bale dischargeGrab-out


07 / QUESTIONS & SUPPORT

Product questions,
answered.

HBK Selection Questions

Six practical answers for the project review.

What should the receiving recycler confirm before selection?

Ask for acceptable material grades, bale dimensions, handling limits and condition requirements. Include those requirements in the quotation information. Agree how representative bales will be checked and handled; appearance alone cannot establish density, integrity or acceptance at the destination.

Which scrap materials does this page cover?

The scope is prepared steel sheet and plate offcuts, subject to material and configuration review. Submit grade, dimensions, thickness and contamination details. The light-gauge ferrous scrap guide provides related application information without establishing the allowable limits of a selected HBK model.

Do dual and twin main cylinders identify different HBK models?

Here, dual and twin both describe two main cylinders in the HBK compression arrangement. These title terms do not establish different hardware, force ratings or production capacities. Confirm the actual machine configuration and operating sequence in the project-specific specification.

Can the demonstration video establish production capacity?

The linked HBK video is identified with twin main cylinders and thin sheet or steel plate scrap. It is contextual product material, not a documented acceptance test. Confirm output using representative feed, complete operating time and the agreed loading and collection methods; do not infer numerical ratings from the video.

What routine hydraulic checks should be planned?

Follow the selected machine's operating and maintenance manual for checks of guards, hydraulic connections, wear surfaces and controls. Stop and report abnormal conditions through the site procedure. Servicing or blockage removal requires authorized isolation of all energy sources. Ask Dershan about model-specific inspection requirements when confirming the equipment.

What should I send for an HBK selection review?

Send material photographs, grade, maximum dimensions and thickness, typical shift quantities, intended operating hours and receiving bale requirements. Include electrical supply information and a site layout with loading and collection equipment. Contact DSBale to review the material and proposed installation before agreeing model-specific specifications.


Equipment Recommendation

Tell Us About Your Material and Capacity

Share the key operating conditions below so our team can compare suitable equipment and prepare a practical configuration.

✓ Material & Capacity Review✓ Configuration Recommendation✓ Pricing & Lead-Time Inquiry

We use this information only to respond to your equipment inquiry.