Metal Balers

Twin Main Cylinder Industrial Scrap Baler

Twin-main-cylinder HBK selection around complete shift operations

Twin Main Cylinder Industrial Scrap Baler from the HBK family, with horizontal hydraulic compression, twin main cylinders and grab-out handling for assessed steel offcuts.

HBK familyTwin main cylindersHydraulic compressionGrab-out bale handling
Suitable materials

PRODUCT VIDEO

Twin Main Cylinder Industrial Scrap Baler video

01 / PRODUCT DESCRIPTION

Shift workflow and handling with HBK

An application-focused presentation of the HBK baler family.

Shift workflow and handling with HBK

HBK family guidance for prepared steel sheet and plate offcuts. Confirm the selected machine and application before ordering.

The Twin Main Cylinder Industrial Scrap Baler is an HBK horizontal hydraulic baler for assessed, prepared metal scrap. The twin main cylinders are part of its compression system, with grab-out collection for the formed bale. This page considers prepared steel sheet and plate offcuts, focusing on the time and handling steps around compression. It describes the same HBK product family rather than a separately rated industrial model.

A workable shift plan connects incoming scrap, loading equipment, baler operation and bale removal. These steps share space and resources, so the availability of a grab or loading operator can influence practical production. Discuss the full operating sequence when defining the required duty, including normal interruptions and collection arrangements.


02 / MATERIALS & OUTPUT

Prepared Steel Sheet and Plate Offcuts

Define the feedstock before specifying the machine.

Build the material description from typical operating conditions. Include flat pieces, curled offcuts and nested sheet where these occur in the actual stream, without treating them as interchangeable loads. Note maximum dimensions and thickness, grade, contamination and the way loose material is presented to the loading equipment. Prepared plate offcuts require a suitability review; the product name does not establish an unrestricted plate-processing capability.

Review short busy periods separately from average shift volume. A baler receiving accumulated scrap after a production run may need a different collection schedule from one receiving small batches throughout the day. This is a workflow question for the project assessment, not proof of a different HBK hardware configuration.


Loose thin strip and sheet-metal offcuts
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.
Formed sheet-metal stamping remnants
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.
Perforated sheet skeletons and trim
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.
Loose bent sheet and strip remnants
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.

03 / STRUCTURE & FEATURES

Equipment features.

HBK-family hydraulic metal baler with twin main cylinders; equipment reference

Twin Main Cylinders and Configuration

Confirm controls, wear components and handling interfaces.

Horizontal hydraulic layout: HBK combines a charging chamber with twin-main-cylinder compression and grab-out bale collection. Confirm the final hydraulic sequence in the selected machine documentation.

Control selection: the series source lists PLC automatic or manual control. Optional remote control requires explicit confirmation in the supply scope.

Wear components: the source identifies interchangeable wear steel plates and NM450 or Hardox450 alternatives. Confirm the selected material and replacement details in the proposal.

Handling interfaces: specify approved loading and bale collection equipment, operating clearances and protected work areas. A grab-out designation does not establish an included crane.

Review guards, interlocks, emergency stops and maintenance access with the final configuration. Product illustrations and a series-level feature list do not replace machine-specific operating instructions or installation documentation.


04 / WORKING PRINCIPLE

Loading, Compression and Grab-out Collection

Plan the complete approved operating sequence.

  1. Prepare: sort approved offcuts, check dimensions and exclude batteries, sealed or pressurized containers and hazardous contamination.

  2. Load: use the approved feeding method with personnel outside the operating zone.

  3. Compress: operate the documented hydraulic sequence under the selected control arrangement.

  4. Collect: remove the bale using suitable grab-out handling equipment and the designated route.

  5. Reset: complete the prescribed checks before the next charge.

Only trained personnel should operate the equipment. Follow the machine manual and site isolation procedures for inspection, clearing obstructions or maintenance, including stored hydraulic energy. Never reach into the chamber or attempt to reposition material during operation.


05 / TECHNICAL REFERENCE

HBK Series Parameters and Selection

Selected source attributes require a model-specific proposal.

The table presents selected HBK series attributes, not a complete model specification. Confirm the final combination, material limits, chamber dimensions, force, power and bale requirements in the technical proposal. Numerical output and bale properties require defined feedstock and operating conditions.

Mechanical attributeHBK series reference / option
Remote controlOptional
Wear-plate material optionsNM450 or Hardox450, according to configuration
DriveHydraulic drive
Feeding alternativesGrabber or manual, subject to the specified installation
LayoutHorizontal
Motor voltageCustomized; confirm site supply and selected model


07 / QUESTIONS & SUPPORT

Product questions,
answered.

HBK Selection Questions

Six practical answers for the project review.

Should shift planning use compression time alone?

No. Include preparation, loading, compression, grab-out collection and normal interruptions. Record accepted bale mass over the complete elapsed operating period. The throughput planning guide explains the distinction between a hydraulic cycle and practical production; agree test conditions before adopting an output target.

Which scrap materials does this page cover?

The scope is prepared steel sheet and plate offcuts, subject to material and configuration review. Submit grade, dimensions, thickness and contamination details. The light-gauge ferrous scrap guide provides related application information without establishing the allowable limits of a selected HBK model.

Do dual and twin main cylinders identify different HBK models?

Here, dual and twin both describe two main cylinders in the HBK compression arrangement. These title terms do not establish different hardware, force ratings or production capacities. Confirm the actual machine configuration and operating sequence in the project-specific specification.

Can the demonstration video establish production capacity?

The linked HBK video is identified with twin main cylinders and thin sheet or steel plate scrap. It is contextual product material, not a documented acceptance test. Confirm output using representative feed, complete operating time and the agreed loading and collection methods; do not infer numerical ratings from the video.

What routine hydraulic checks should be planned?

Follow the selected machine's operating and maintenance manual for checks of guards, hydraulic connections, wear surfaces and controls. Stop and report abnormal conditions through the site procedure. Servicing or blockage removal requires authorized isolation of all energy sources. Ask Dershan about model-specific inspection requirements when confirming the equipment.

What should I send for an HBK selection review?

Send material photographs, grade, maximum dimensions and thickness, typical shift quantities, intended operating hours and receiving bale requirements. Include electrical supply information and a site layout with loading and collection equipment. Contact DSBale to review the material and proposed installation before agreeing model-specific specifications.


Equipment Recommendation

Tell Us About Your Material and Capacity

Share the key operating conditions below so our team can compare suitable equipment and prepare a practical configuration.

✓ Material & Capacity Review✓ Configuration Recommendation✓ Pricing & Lead-Time Inquiry

We use this information only to respond to your equipment inquiry.