Metal Balers

Twin Main Cylinder Scrap Recycling Baler

HBK selection around prepared offcuts and recycler receiving requirements

Twin Main Cylinder Scrap Recycling Baler from the HBK family, with horizontal hydraulic compression and grab-out collection for assessed, prepared steel sheet and plate offcuts.

HBK familyTwin main cylindersHydraulic compressionGrab-out bale handling
Suitable materials

PRODUCT VIDEO

Twin Main Cylinder Scrap Recycling Baler video

01 / PRODUCT DESCRIPTION

Receiving Requirements and Scrap Recycling with HBK

Define the application before choosing a machine specification.

Receiving Requirements and Scrap Recycling with HBK

HBK family guidance for prepared steel sheet and plate offcuts. Confirm the selected machine and application before ordering.

The Twin Main Cylinder Scrap Recycling Baler is an application presentation of the HBK horizontal hydraulic baler family. Twin main cylinders form part of the compression arrangement, and completed bales are collected by grab-out handling. This page covers prepared steel sheet and plate offcuts, with particular attention to the receiving recycler’s requirements. The title does not establish a separate model, a fixed output rating or approval for every type of scrap metal.

Start selection by agreeing what the receiving operation needs. Identify acceptable grades, contamination restrictions and bale handling requirements before defining the equipment proposal. Bring together the people responsible for scrap preparation, loading, bale collection and transport so the intended recycling route can be assessed as a complete workflow.


02 / MATERIALS & OUTPUT

Prepared Steel Sheet and Plate Offcuts

Describe representative material and preparation requirements.

Describe the actual offcuts rather than relying on a broad label such as mixed steel. Record grade, maximum dimensions, actual thickness, shape and surface condition. Explain whether batches contain flat blanks, curled strips or nested remnants, and whether these forms are kept separate. Review unusual pieces explicitly rather than assuming they are covered by the typical batch description.

Receiving requirements may determine how material is segregated before baling. Record any restrictions on mixed grades or contamination and explain how approved material will be identified at the loading point. Photographs should show individual pieces and a representative loose batch. Material pictures and completed bale examples illustrate forms; they do not establish measured HBK production results or receiving acceptance.


Loose thin strip and sheet-metal offcuts
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.
Formed sheet-metal stamping remnants
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.
Perforated sheet skeletons and trim
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.
Loose bent sheet and strip remnants
Steel-sheet material reference. Confirm grade, thickness, dimensions and preparation for the selected HBK configuration; not a matched HBK production trial.

03 / STRUCTURE & FEATURES

Equipment features.

HBK-family hydraulic metal baler with twin main cylinders; equipment reference

Compression, Controls and Handling Interfaces

Review series features against the selected supply scope.

Horizontal hydraulic layout: HBK combines a charging chamber with twin-main-cylinder compression and grab-out bale collection. Confirm the final hydraulic sequence in the selected machine documentation.

Control selection: the series source lists PLC automatic or manual control. Optional remote control requires explicit confirmation in the supply scope.

Wear components: the source identifies interchangeable wear steel plates and NM450 or Hardox450 alternatives. Confirm the selected material and replacement details in the proposal.

Handling interfaces: specify approved loading and bale collection equipment, operating clearances and protected work areas. A grab-out designation does not establish an included crane.

Review guards, interlocks, emergency stops and maintenance access with the final configuration. Product illustrations and a series-level feature list do not replace machine-specific operating instructions or installation documentation.


04 / WORKING PRINCIPLE

Approved Loading and Baling Sequence

Coordinate safe preparation, compression and bale collection.

  1. Prepare: sort approved offcuts, check dimensions and exclude batteries, sealed or pressurized containers and hazardous contamination.

  2. Load: use the approved feeding method with personnel outside the operating zone.

  3. Compress: operate the documented hydraulic sequence under the selected control arrangement.

  4. Collect: remove the bale using suitable grab-out handling equipment and the designated route.

  5. Reset: complete the prescribed checks before the next charge.

Only trained personnel should operate the equipment. Follow the machine manual and site isolation procedures for inspection, clearing obstructions or maintenance, including stored hydraulic energy. Never reach into the chamber or attempt to reposition material during operation.


05 / TECHNICAL REFERENCE

HBK Series Parameters and Selection

Selected attributes require a model-specific technical proposal.

The table presents selected HBK series attributes, not a complete model specification. Confirm the final combination, material limits, chamber dimensions, force, power and bale requirements in the technical proposal. Numerical output and bale properties require defined feedstock and operating conditions.

Mechanical attributeHBK series reference / option
Remote controlOptional
Construction steelQ235B; machine construction steel
Motor voltageCustomized; confirm site supply and selected model
Wear-plate material optionsNM450 or Hardox450, according to configuration
Bale dischargeGrab-out
Control optionsPLC automatic or manual control, according to configuration


07 / QUESTIONS & SUPPORT

Product questions,
answered.

HBK Project Questions

Six practical answers for material and procurement review.

What should be agreed with the receiving recycler?

Confirm accepted material grades, contamination restrictions, bale dimensions and handling limits. Include these requirements in the quotation checklist so the technical proposal addresses the intended destination. A bale’s appearance cannot establish its mass, density or acceptance by a receiving operation.

Can several sheet grades be combined in one charge?

Explain the intended mixture and any downstream grade requirements before selection. Keep streams separate when their receiving requirements call for it. The stamping steel scrap application guide provides relevant context, but suitability of a specific mixture depends on the material review and the selected configuration.

What does twin main cylinder mean for this product?

It describes two main cylinders in the HBK compression arrangement. It does not identify a second hardware variant or prove a particular force, cycle time or energy consumption. The machine-specific specification must define the actual arrangement and operating sequence.

How should a representative bale evaluation be planned?

Use offcuts that reflect the normal material stream, including relevant variations in dimensions and shape. Agree preparation, loading and grab-out methods in advance. Assess bale dimensions, mass and condition against the receiving requirements under the documented handling procedure, rather than judging photographs alone.

Does a short compression cycle establish recycling output?

No. Include material preparation, loading, compression, collection and normal interruptions in production planning. The production planning guide explains why complete operating time matters. Agree the conditions and measurement method before treating an output figure as relevant to the proposed recycling operation.

What information supports a receiving-focused quotation?

Provide offcut photographs and dimensions, grade, thickness, expected shift quantities, receiving bale requirements and a layout showing loading and collection. Identify any constraints imposed by transport or downstream handling equipment. Then contact Dershan to discuss a model-specific selection and the proposed evaluation scope.


Equipment Recommendation

Tell Us About Your Material and Capacity

Share the key operating conditions below so our team can compare suitable equipment and prepare a practical configuration.

✓ Material & Capacity Review✓ Configuration Recommendation✓ Pricing & Lead-Time Inquiry

We use this information only to respond to your equipment inquiry.